With new cap that seals the bottle so it won't leak. Ideal for tool boxes and other places you don't want your CA glue to spill.

A water thin CA that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam.

With new cap that seals the bottle so it won't leak. Ideal for tool boxes and other places you don't want your CA glue to spill.

A higher viscosity CA for lose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds.

With new cap that seals the bottle so it won't leak. Ideal for tool boxes and other places you don't want your CA glue to spill.

Extra thick CA. The best CA for for most plastics, including GE's Lexan. It works as a puddy for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic.

Extra thick CA. The best CA for for most plastics, including GE's Lexan. It works as a puddy for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. Bond fiberglass, carbon fiber, hardwood, metal and rubber better than most other hobby adhesives.

A toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberghlass, rubber, carbon fiber and advanced materials. For model use IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages.

Setup time is 20-40 seconds, which can be accelerated with INSTA-SET. When cured, IC-2000 is pliable enough to be carved with a hobby knife. IC-2000 is the best adhesive for R/C car tires.

A toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberghlass, rubber, carbon fiber and advanced materials. For model use IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET. When cured, IC-2000 is pliable enough to be carved with a hobby knife. IC-2000 is the best adhesive for R/C car tires.

Thin flexible toughened CA. When cured INSTA-FLEX thin does not turn brittle and remains clear, even if accelerated with INSTA-CURE. It has superior shock resistance. Although not as thin in consistance as INSTA-CURE, INSTA-FLEX has good penetrating qualities and its application can be easier to control. Ideal for many applications, including the installation of CA hinges. We recommend drilling a 1/16" hole in the center of the hinge slot to insure the complete saturation of the hinge. INSTA-FLEX has a different less irritating odor compared to regular CA's, but still can not be used on hot wire foam.

A clear toughened CA with similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. The carbon component of the IC-2000 that gives the CA its black color also contributes to its unsurpassed strength.

INSTA-FLEX is superior in strength to standard CA but a little lower in strength compared to our IC-2000. When a joint is a larger than normal gap, flexible CA's provide superior shock resistant bonds.

Now with the New Pocket CA Caps which seal the bottles so it won't leak and it stays fresher longer.

Oderless cyanoacrylate is formulated for use by those persons who have become sensitive or allergic to standard CA. They can be used on materials such as hot wire foams that are otherwise dissolved or frosted by standard CA. They can be used in the building of foam core wings and the assembly and repair of plastic and foam models.

Oderless cyanoacrylate is formulated for use by those persons who have become sensitive or allergic to standard CA. They can be used on materials such as hot wire foams that are otherwise dissolved or frosted by standard CA. Therefore they can be used in the building of foam core wings and the assembly and repair of plastic and foam models.

Spray bottle catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from the joint when parts are pressed together. Applying an additional bead of thick CA along the seam then curing it with INSTA-SET significantly enhances the joints strength. INSTA-SET activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastics and white foam.

8 oz refill for the 2 oz spray bottle.

Softens cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers.