Super Thin, (1-3 second cure) has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. Thin CA's work very well on balsa since they pernitrate into the wood and form more than just a surface bond. Each bottle includes (3) three extender tips.

Includes (3) extender tips

Includes (3) extender tips

Includes (3) extender tips

Extra thick CA. (10-25 sec. cure) The best CA for for most plastics, including GE's Lexan. It works as a puddy for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. Bond fiberglass, carbon fiber, hardwood, metal and rubber better than most other hobby adhesives.Each bottle includes (3) extender tips.

A toughened cyanoacrylate (20-45 sec. cure) that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon fiber and advanced materials. For model use IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET. When cured, IC-2000 is pliable enough to be carved with a hobby knife. IC-2000 is the best adhesive for R/C car tires. Each bottle includes (3) extender tips.

Clear toughened CA.(5-15 sec. cure) with similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. The carbon component of the IC-2000 that gives the CA its black color also contributes to its unsurpassed strength. INSTA-FLEX is superior in strength to standard CA but a little lower in strength compared to our IC-2000. When a joint is a larger than normal gap, flexible CA's provide superior shock resistant bonds. Each bottle includes (3) extender tips.

Thin Odorless 100% foam safe. (3-5 sec. cure) cyanoacrylate is formulated for use by those persons who have become sensitive or allergic to standard CA. They can be used on materials such as hot wire foams that are otherwise dissolved or frosted by standard CA. They are 100% foam safe therefore they can be used in the building of foam core wings and the assembly and repair of plastic and foam models. Each bottle includes (3) extender tips.

Includes (3) extender tips.

Insta-set catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from the joint when parts are pressed together. Applying an additional bead of thick CA along the seam then curing it with INSTA-SET significantly enhances the joints strength. INSTA-SET activates CA in (6 to 8 seconds) without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastics and white foam.

Softens cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Each bottle includes (3) extender tips.

Includes (3) extender tips.

Includes (3) extender tips.

Includes (3) extender tips.

A higher viscosity CA (5-10 sec. cure) for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held together tightly for about 5 to 15 seconds. For large surfaces including those with close fitting joints such as laminates INSTA CURE+ should also be used. To prevent premature curing don't spread the glue to thin, lay down a serpentine bead about 1" separation's on one surface then assemble. Each bottle includes (3) extender tips.